Nearly everybody may have their private idea involving Installing A Bathtub.
Installing a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult task. If the old tub is easily easily accessible, the task can move immediately; if you have to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to leave the old tub as well as embeded in the new one. Ensure you have certified on your own for the job as well as fit trying it. As opposed to working with a specialist to take control of a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bath tub in your restroom if you have actually currently gotten a brand-new bathtub and also do not need to alter the setup of your previous supply of water pipelines.
Your devices and material list should make up the following:
Preparing for the Setup
To start with, the sustaining structure provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before moving on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the tub in the called for setting. The wooden boards are practical in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to make sure that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water and inspect all joints and also new pipework for leaks and tighten them if essential. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that piece on How to Install a Bathtub Yourself while exploring the internet. Sharing is good. Helping others is fun. I treasure reading our article about Installing A Bathtub.
Book Services